Nissan Versa (N17): P0137 HO2s2

DTC Logic

DTC DETECTION LOGIC

The heated oxygen sensor 2 has a much longer switching time between rich and lean than the air fuel ratio (A/F) sensor 1. The oxygen storage capacity of the three way catalyst 1 causes the longer switching time. To judge the malfunctions of heated oxygen sensor 2, ECM monitors whether the maximum voltage of the sensor is sufficiently high during various driving conditions such as fuelcut.

DTC DETECTION LOGIC

DTC No. Trouble diagnosis name DTC detecting condition Possible cause
P0137 Heated oxygen sensor 2 circuit low voltage The maximum voltage from the sensor does not reach the specified voltage.
  • Harness or connectors (The sensor circuit is open or shorted)
  • Heated oxygen sensor 2
  • Fuel pressure
  • Fuel injector
  • Intake air leaks

DTC CONFIRMATION PROCEDURE

1.INSPECTION START

Do you have CONSULT?

YES >> GO TO 2.

NO >> GO TO 5.

2.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION: For better results, perform "DTC WORK SUPPORT" at a temperature of 0 to 30C (32 to 86F).

>> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch ON and select "DATA MONITOR" mode of "ENGINE" using CONSULT.
  2. Start engine and warm it up to normal operating temperature.
  3. Turn ignition switch OFF and wait at least 10 seconds.
  4. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
  5. Let engine idle for 1 minute.
  6. Make sure that "COOLAN TEMP/S" indicates more than 70C (158F).

    If not, warm up engine and go to next step when "COOLAN TEMP/S" indication reaches 70C (158F).

  7. Open engine hood.
  8. Select "HO2S2 (B1) P1147" of "HO2S2" in "DTC WORK SUPPORT" mode of "ENGINE" using CONSULT.
  9. Follow the instruction of CONSULT.

    NOTE: It will take at most 10 minutes until "COMPLETED" is displayed.

  10. Touch "SELFDIAG RESULT".

Which is displayed on CONSULT screen?

OK >> INSPECTION END

NG >> Proceed to EC, "Diagnosis Procedure".

CAN NOT BE DIAGNOSED>>GO TO 4.

4.PERFORM DTC CONFIRMATION PROCEDURE AGAIN

  1. Turn ignition switch OFF and leave the vehicle in a cool place (soak the vehicle).
  2. Perform DTC CONFIRMATION PROCEDURE again.

>> GO TO 3.

5.PERFORM COMPONENT FUNCTION CHECK

Perform component function check. Refer to EC, "Component Function Check".

NOTE: Use component function check to check the overall function of the heated oxygen sensor 2 circuit. During this check, a 1st trip DTC might not be confirmed.

Is the inspection result normal?

YES >> INSPECTION END

NO >> Proceed to EC, "Diagnosis Procedure".

Component Function Check

1.PERFORM COMPONENT FUNCTION CHECKI

Without CONSULT

  1. Start engine and warm it up to the normal operating temperature.
  2. Turn ignition switch OFF and wait at least 10 seconds.
  3. Restart engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
  4. Let engine idle for 1 minute.
  5. Check the voltage between ECM harness connector terminals under the following condition.

PERFORM COMPONENT FUNCTION CHECKI

Is the inspection result normal?

YES >> INSPECTION END

NO >> GO TO 2.

2.PERFORM COMPONENT FUNCTION CHECKII

Check the voltage between ECM harness connector terminals under the following condition.

PERFORM COMPONENT FUNCTION CHECKII

Is the inspection result normal?

YES >> INSPECTION END

NO >> GO TO 3.

3.PERFORM COMPONENT FUNCTION CHECKIII

Check the voltage between ECM harness connector terminals under the following condition.

PERFORM COMPONENT FUNCTION CHECKIII

Is the inspection result normal?

YES >> INSPECTION END

NO >> Go to EC, "Diagnosis Procedure".

Diagnosis Procedure

1.HECK GROUND CONNECTION

  1. Turn ignition switch OFF.
  2. Check ground connection E15. Refer to Ground Inspection in GI, "Circuit Inspection".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CLEAR THE MIXTURE RATIO SELFLEARNING VALUE

  1. Clear the mixture ratio selflearning value. Refer to EC, "Work Procedure".
  2. Run engine for at least 10 minutes at idle speed.

Is the 1st trip DTC P0171 detected? Is it difficult to start engine?

YES >> Perform trouble diagnosis for DTC P0171. Refer to EC, "DTC Logic".

NO >> GO TO 3.

3.CHECK HO2S2 GROUND CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.
  2. Disconnect heated oxygen sensor 2 harness connector.
  3. Disconnect ECM harness connector.
  4. Check the continuity between HO2S2 harness connector and ECM harness connector.

CHECK HO2S2 GROUND CIRCUIT FOR OPEN AND SHORT

    5.   Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> GO TO 4.

NO >> Repair open circuit, short to ground or short to power in harness or connectors.

4.CHECK HO2S2 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

    1.   Check the continuity between HO2S2 harness connector and ECM harness connector.

CHECK HO2S2 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

    2.   Check the continuity between HO2S2 harness connector ground or ECM harness connector and ground.

CHECK HO2S2 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

CHECK HO2S2 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

    3.   Also check harness for short to power.

Is the inspection result normal?

YES >> GO TO 5.

NO >> Repair open circuit, short to ground or short to power in harness or connectors.

5.CHECK HEATED OXYGEN SENSOR 2

Refer to EC, "Component Inspection".

Is the inspection result normal?

YES >> GO TO 7.

NO >> GO TO 6.

6.REPLACE HEATED OXYGEN SENSOR 2

Replace malfunctioning heated oxygen sensor 2. Refer to EX, "Exploded View"

CAUTION:

  • Discard any heated oxygen sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard surface such as a concrete floor; use a new one.
  • Before installing new oxygen sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner [commercial service tool (J4389718 or J4389712)] and approved antiseize lubricant (commercial service tool).

>> INSPECTION END

7.CHECK INTERMITTENT INCIDENT

Refer to GI, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.INSPECTION START

Do you have CONSULT?

YES >> GO TO 2.

NO >> GO TO 3.

2.CHECK HEATED OXYGEN SENSOR 2

With CONSULT

  1. Turn ignition switch ON and select "ENGINE" using CONSULT.
  2. Select "DATA MONITOR" mode.
  3. Start engine and warm it up to the normal operating temperature.
  4. Turn ignition switch OFF and wait at least 10 seconds.
  5. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
  6. Let engine idle for 1 minute.
  7. Select "FUEL INJECTION" in "ACTIVE TEST" mode, and select "HO2S2 (B1)" as the monitor item with CONSULT.
  8. Check "HO2S2 (B1)" at idle speed when adjusting "FUEL INJECTION" to +-25%.

CHECK HEATED OXYGEN SENSOR 2

"HO2S2 (B1)" should be above 0.68 V at least once when the "FUEL INJECTION" is +25%.

"HO2S2 (B1)" should be below 0.36 V at least once when the "FUEL INJECTION" is −25%.

Is the inspection result normal?

YES >> INSPECTION END

NO >> GO TO 6.

3.CHECK HEATED OXYGEN SENSOR 2I

Without CONSULT

  1. Start engine and warm it up to the normal operating temperature.
  2. Turn ignition switch OFF and wait at least 10 seconds.
  3. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
  4. Let engine idle for 1 minute.
  5. Check the voltage between ECM harness connector terminals under the following condition.

CHECK HEATED OXYGEN SENSOR 2I

Is the inspection result normal?

YES >> INSPECTION END

NO >> GO TO 4.

4.CHECK HEATED OXYGEN SENSOR 2II

Check the voltage between ECM harness connector terminals under the following condition.

CHECK HEATED OXYGEN SENSOR 2II

Is the inspection result normal?

YES >> INSPECTION END

NO >> GO TO 5.

5.CHECK HEATED OXYGEN SENSOR 2III

Check the voltage between ECM harness connector terminals under the following condition.

CHECK HEATED OXYGEN SENSOR 2III

Is the inspection result normal?

YES >> INSPECTION END

NO >> GO TO 6.

6.REPLACE HEATED OXYGEN SENSOR 2

Replace malfunctioning heated oxygen sensor 2. Refer to EX, "Exploded View".

CAUTION:

  • Discard any heated oxygen sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard surface such as a concrete floor; use a new one.
  • Before installing new oxygen sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner [commercial service tool (J4389718 or J4389712)] and approved antiseize lubricant (commercial service tool).

>> INSPECTION END

Other materials:

How to select piston and bearing
Description Selection points Selection parts Selection items Selection methods Between cylinder block and crankshaft Main bearing Main bearing grade (bearing thickness) Determined by match of cylinder block bearing housing grade (inner diameter of housi ...

Diagnosis system (EPS control unit)
CONSULT Function FUNCTION CONSULT can display each diagnostic item using the diagnostic test modes shown following.    *: The following diagnosis information is erased by erasing. DTC Freeze frame data (FFD) ECU IDENTIFICATION Displays the part number stored in the con ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0085