Nissan Versa (N17): Precautions

Nissan Versa 2nd generation (N17) Service Manual / Body exterior, doors, roof & vehicle security / Power window control system (PWC) / Precautions

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"

The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.

Information necessary to service the system safely is included in the SR and SB section of this Service Manual.

WARNING:

  • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer.
  • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SR section.
  • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

  • When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury.
  • When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery, and wait at least 3 minutes before performing any service.

Precaution for Work

  • When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth.
  • When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
  • Protect the removed parts with a shop cloth and prevent them from being dropped.
  • Replace a deformed or damaged clip.
  • If a part is specified as a non-reusable part, always replace it with a new one.
  • Be sure to tighten bolts and nuts securely to the specified torque.
  • After installation is complete, be sure to check that each part works properly.
  • Follow the steps below to clean components:

- Water soluble dirt:

  • Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
  • Then rub with a soft, dry cloth.

- Oily dirt:

  • Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
  • Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
  • Then rub with a soft, dry cloth.

- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.

- For genuine leather seats, use a genuine leather seat cleaner.

PREPARATION

Special Service Tool

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Special Service Tool

SYSTEM DESCRIPTION

COMPONENT PARTS

Component Parts Location

Component Parts Location

1. BCM (view with instrument panel removed) 2. Front power window motor (view with front door finisher removed) 3. Rear power window motor (view with rear door finisher removed) 4. Main power window and door lock/ unlock switch 5. Front power window and door lock/ unlock switch RH 6. Rear power window switch 7. Front door switch LH (RH similar)

Component Description

Rear regulator

Exploded View 1. Rear door panel 2. Sealing screen 3. Rear door sash 4. Rear power window motor 5. Regulator assembly 6. Partition sash 7. Partition glass 8. Rear door glass 9. Partition weathe ...

System

System Diagram System Description BASIC OPERATION Power window system is activated by power window switch when ignition switch turns ON. Power window main switch opens/closes all door ...

Other materials:

Camshaft valve clearance
Inspection and Adjustment INSPECTION Perform inspection as follows after removal, replacement or installation of camshaft or valverelated parts, or if there are unusual engine conditions regarding valve clearance. Remove rocker cover. Measure the valve clearance with the following proced ...

Component parts
Component Parts Location 1. Crash zone sensor 2. Front door satellite sensor LH 3. Spiral cable 4. Front passenger air bag off indicator 5. Front LH seatbelt pre-tensioner Side air bag satellite sensor LH 6. Air bag diagnosis sensor unit 7. Front LH side air bag module 8. Seat belt buckle ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0072