Nissan Versa (N17): P0116 ECT sensor

DTC Logic

DTC DETECTION LOGIC

DTC No. Trouble diagnosis name (Trouble diagnosis content) DTC detecting condition Possible cause
P0116 ECT SEN/CIRC [Engine coolant temperature (ECT) sensor circuit range/performance] The comparison result of signals transmitted to ECM from each temperature sensor (IAT sensor, ECT sensor, FTT sensor, and EOT sensor) shows that the voltage signal of the ECT sensor is higher/lower than that of other temperature sensors when the engine is started with its cold state.
  • Harness or connectors (High or low resistance in the ECT sensor circuit)
  • ECT sensor

DTC CONFIRMATION PROCEDURE

1.INSPECTION START

Is it necessary to erase permanent DTC?

YES >> GO TO 3.

NO >> GO TO 2.

2.PERFORM COMPONENT FUNCTION CHECK

Perform component function check. Refer to EC, "Component Function Check".

NOTE: Use the component function check to check the overall function of the ECT sensor circuit. During this check, a 1st trip DTC might not be confirmed.

Is the inspection result normal?

YES >> INSPECTION END

NO >> Proceed to EC193, "Diagnosis Procedure".

3.PRECONDITIONING

If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

  • Before performing the following procedure, do not add fuel.
  • Before performing the following procedure, check that fuel level is between 1/4 and 4/4.
  • Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>> GO TO 4.

4.PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 60 minutes.
  2. Move the vehicle to a cool place.

    NOTE: Cool the vehicle in an environment of ambient air temperature between −10C (14F) and 35C (95F).

  3. Turn ignition switch OFF and soak the vehicle for 12 hours.

    CAUTION: Never turn ignition switch ON during soaking.

    NOTE: The vehicle must be cooled with the food open.

  4. Start engine and let it idle for 5 minutes or more.

    CAUTION: Never turn ignition switch OFF during idling.

  5. Check 1st trip DTC.

Is 1st trip DTC detected?

YES >> Proceed to EC, "Diagnosis Procedure".

NO >> INSPECTION END

Component Function Check

1.CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR

  1. Turn ignition switch OFF.
  2. Disconnect ECT sensor harness connector.
  3. Remove ECT sensor. Refer to CO, "Exploded View".
  4. Check resistance between ECT sensor terminals by heating with hot water as shown in the figure.

CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR

CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR

Is the inspection result normal?

YES >> Check intermittent incident. Refer to GI, "Intermittent Incident".

NO >> Proceed to EC, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR

Check ECT sensor. Refer to EC, "Component Inspection".

Is the inspection result normal?

YES >> Check intermittent incident. Refer to GI, "Intermittent Incident".

NO >> Replace ECT sensor. Refer to CO, "Exploded View".

Component Inspection

1.CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR

  1. Turn ignition switch OFF.
  2. Disconnect ECT sensor harness connector.
  3. Remove ECT sensor.
  4. Check resistance between ECT sensor terminals by heating with hot water as shown in the figure.

CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR

CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR

Is the inspection result normal?

YES >> INSPECTION END

NO >> Replace engine coolant temperature sensor. Refer to CO, "Exploded View".

Other materials:

Intake manifold
Exploded View 1. EVAP canister purge volume control solenoid valve 2. Hose clamp 3. Vacuum hose 4. PCV hose 5. Hose clamp 6. Intake manifold support 7. Gasket 8. Intake manifold 9. Electric throttle control actuator 10. Gasket 11. EVAP service port A. To air duct B. To centralized underf ...

OD OFF indicator lamp
Component Function Check 1.CHECK OD OFF INDICATOR LAMP FUNCTION Check OD OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON. Is the inspection results normal? YES >> INSPECTION END NO >> Go to TM "Diagnosis Procedure". Diagnosis Procedure ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0222