Nissan Versa (N17): P0111 IAT sensor

DTC Logic

DTC DETECTION LOGIC

DTC No. Trouble diagnosis name (Trouble diagnosis content) DTC detecting condition Possible cause
P0111 IAT SENSOR 1 B1 [Intake air temperature (IAT) sensor circuit range/performance] The comparison result of signals transmitted to ECM from each temperature sensor (IAT sensor, ECT sensor, FTT sensor, and EOT sensor) shows that the voltage signal of the IAT sensor is higher/lower than that of other temperature sensors when the engine is started with its cold state.
  • Harness or connectors (High or low resistance in the IAT sensor circuit)
  • IAT sensor

DTC CONFIRMATION PROCEDURE

1.INSPECTION START

Is it necessary to erase permanent DTC?

YES >> GO TO 3.

NO >> GO TO 2.

2.PERFORM COMPONENT FUNCTION CHECK

Perform component function check. Refer to EC, "Component Function Check".

NOTE: Use the component function check to check the overall function of the IAT sensor circuit. During this check, a 1st trip DTC might not be confirmed.

Is the inspection result normal?

YES >> INSPECTION END

NO >> Proceed to EC, "Diagnosis Procedure".

3.PRECONDITIONING

If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

  • Before performing the following procedure, do not add fuel.
  • Before performing the following procedure, check that fuel level is between 1/4 and 4/4.
  • Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>> GO TO 4.

4.PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 60 minutes.
  2. Move the vehicle to a cool place.

    NOTE: Cool the vehicle in an environment of ambient air temperature between −10C (14F) and 35C (95F).

  3. Turn ignition switch OFF and soak the vehicle for 12 hours.

    CAUTION: Never turn ignition switch ON during soaking.

    NOTE: The vehicle must be cooled with the food open.

  4. Start engine and let it idle for 5 minutes or more.

    CAUTION: Never turn ignition switch OFF during idling.

  5. Check 1st trip DTC.

Is 1st trip DTC detected?

YES >> Proceed to EC, "Diagnosis Procedure".

NO >> INSPECTION END

Component Function Check

1.CHECK INTAKE AIR TEMPERATURE (IAT) SENSOR

  1. Turn ignition switch OFF.
  2. Disconnect mass air flow sensor harness connector.
  3. Check resistance between mass air flow sensor terminals as follows.

CHECK INTAKE AIR TEMPERATURE (IAT) SENSOR

Is the inspection result normal?

YES >> Check intermittent incident. Refer to GI, "Intermittent Incident".

NO >> Proceed to EC, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK INTAKE AIR TEMPERATURE (IAT) SENSOR

Check intake air temperature sensor. Refer toEC, "Component Inspection".

Is the inspection result normal?

YES >> Check intermittent incident. Refer to GI, "Intermittent Incident".

NO >> Replace mass air flow sensor (with intake air temperature sensor). Refer to EM, "Removal and Installation".

Component Inspection

1.CHECK INTAKE AIR TEMPERATURE SENSOR

  1. Turn ignition switch OFF.
  2. Disconnect mass air flow sensor harness connector.
  3. Check resistance between mass air flow sensor terminals as per the following.

CHECK INTAKE AIR TEMPERATURE SENSOR

Is the inspection result normal?

YES >> INSPECTION END

NO >> Replace mass air flow sensor (with intake air temperature sensor). Refer to EM, "Removal and Installation".

Other materials:

Vehicle Dynamic Control (VDC) off switch
The vehicle should be driven with the VDC system on for most driving conditions. If the vehicle is stuck in mud or snow, the VDC system reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine po ...

EVAP control system pressure sensor
Exploded View 1. EVAP control system pressure sensor 2. O-ring 3. EVAP canister Removal and Installation NOTE: The EVAP canister system pressure sensor can be removed without removing the EVAP canister. REMOVAL Remove the EVAP canister protector cover. Disconnect EVAP canister purg ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.008