Nissan Versa (N17): A/T Shift selector
Exploded View

1. Shift selector handle 2. Lock pin 3. Shift selector handle cover
4. Position indication panel 5. Shift selector assembly
Removal and Installation
CAUTION:
Always apply the parking brake before performing removal and installation.
REMOVAL
- Move the shift selector to the "N" position.
- Remove the shift selector handle. Refer to TM "Disassembly and
Assembly".
- Remove the center console. Refer to IP "Removal and Installation".
- Disconnect the harness connector from the shift selector.
- Move the shift selector to the "P" position.
- Remove the key interlock cable from the shift selector assembly. Refer
to TM "Removal and Installation".
- Remove the control cable from the shift selector assembly. Refer to TM
"Removal and Installation".
- Remove the shift selector assembly.
INSTALLATION
Installation is in the reverse order of removal.
- When connecting the control cable (1) to the shift selector assembly
(2), face the grooved surface of the rib (A) up and insert the
control cable until it stops.

Disassembly and Assembly
DISASSEMBLY
- Slide the shift selector handle cover (1) down.
CAUTION:
Do not damage the shift selector handle cover.
- Pull out the lock pin (2).
- Pull the shift selector handle (3) and shift selector handle cover
upward to remove them.
- Remove the position lamp.

- Disengage the hooks (A) (4 locations), and lift up the position
indication panel (1) to separate it from the shift selector assembly
(2).
CAUTION:
Do not damage the shift selector assembly.

ASSEMBLY
Assembly is in the reverse order of disassembly.
- Follow the procedure below to install the shift selector handle.
- Install the lock pin (2) onto the shift selector handle (3).
- Install the shift selector handle cover (1) onto the shift selector
handle.
- Press the shift selector handle onto the shift selector until it
clicks.
CAUTION:- When pressing the shift selector handle onto the shift
selector, do not press the shift selector handle button. - Do not strike the
shift selector handle to install it into place.
- After installing shift selector handle, pull the handle to check that
it does not become disconnected.

Inspection and Adjustment
INSPECTION
- Move the shift selector to "P" position, and turn ignition switch ON.
- Check that shift selector can be moved to other than "P" position when
brake pedal is depressed. Also
check that shift selector can be moved from "P" position only when brake
pedal is depressed.
- Move the shift selector and check for excessive effort, sticking, noise
or rattle.
- Check that shift selector stops at each position with the feel of
engagement when it is moved through all
the positions. Check that the actual position of shift selector matches the
position shown by shift position
indicator and manual lever on the transaxle.
- The method of operating shift selector to individual positions correctly
should be as shown.
- When shift selector handle button is pressed in "P", "R", "N", "D",
"2" or "1" position without applying forward/backward force to
shift selector, check button operation for sticking.
- Check that back-up lamps illuminate only when shift selector is
placed in the "R" position.
- Check that back-up lamps do not illuminate when shift selector
is pushed toward the "R" position when in the "P" or "N" position.
CAUTION:
Check the lighting without pressing shift selector handle
button.
- Check that the engine can only be started with shift selector in the "P"
and "N" positions.
- Check that transaxle is locked completely when shift selector is in "P"
position.

ADJUSTMENT
- Move shift selector to " P" position.
CAUTION:
Rotate the wheels at least a quarter turn and be certain the transaxle is
locked in the "P" position.
- Loosen the control cable nut (A).
- Place manual lever (B) to "P" position.
CAUTION:
Do not apply force to the manual lever.
- Tighten the control cable nut. Refer to TM "Exploded View".
CAUTION:
Do not move the manual lever when tightening.

Inspection
FLUID LEAKAGE
Check transaxle surrounding area (oil seal and plug etc.)for fluid
leakage.
If anything is found, repair or replace damaged parts and adjust A/
T fluid level. Ref ...
Exploded View
1. Bracket B 2. Lock plate 3. Transaxle assembly
4. Bracket A 5. Control cable 6. Shift selector assembly
A: Manual lever B: Grommet
Removal and Installation
CAUTION:
Always ap ...
Other materials:
Air cleaner filter
Exploded View
1. Clamp 2. PCV hose 3. Clamp
4. Mount rubber 5. Air duct (inlet) 6. Air cleaner body
7. Grommet 8. Air cleaner filter 9. Air cleaner cover
10. Mass air flow sensor 11. Air duct 12. Clamp
Removal and Installation
REMOVAL
1. Unhook clips (A) and pull the air cleaner cover u ...
Electric ignition system
ELECTRIC IGNITION SYSTEM : System Diagram
ELECTRIC IGNITION SYSTEM : System Description
INPUT/OUTPUT SIGNAL CHART
Sensor
Input signal to ECM
ECM function
Actuator
Crankshaft position sensor (POS)
Engine speed*3
Piston position
Ignition timing control
Igni ...
© 2017-2025 Copyright www.niveguide.com
0.0074