Nissan Versa (N17): Transaxle assembly

Exploded View

Exploded View

1. Transaxle assembly : Refer to "INSTALLATION" in TM, "Removal and Installation" for the locations and tightening torque.

Removal and Installation

CAUTION: Do not reuse CSC (concentric slave cylinder). CSC slides back to the original position every time transaxle assembly is removed. Dust on the sliding parts may damage the seal of CSC and may cause clutch fluid leakage. Refer to CL, "Removal and Installation".

NOTE: When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spilling.

REMOVAL

  1. Move the shift selector to the neutral position.
  2. Remove battery. Refer to PG, "Removal and Installation".
  3. Remove air cleaner case. Refer to EM, "Removal and Installation".
  4. Remove IPDM E/R bracket bolts (A) and nut (B).

: Front

REMOVAL

  1. Remove IPDM E/R bracket (1).
  2. Remove air breather hose. Refer to TM, "Removal and Installation".
  3. Disconnect selector cable and shifter cable from transaxle assembly. Refer to TM, "Removal and Installation".
  4. Remove drive shaft heat insulator.
  5. Remove crankshaft position sensor. Refer to EM, "Exploded View".
  6. Remove clutch tube clip from engine mounting bracket (LH).
  7. Remove clutch tube from CSC and then temporarily position it aside. Refer to CL, "Removal and Installation".

CAUTION:

  • Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately and wash the affected area with water.
  • Do not depress clutch pedal during removal procedure.
  1. Remove fender protector (LH). Refer to EXT, "Removal and Installation".
  2. Disconnect ground cable.
  3. Disconnect harness connector (A) from position switch.
  4. Remove the harness clamp from rear housing.
  5. Remove the engine harness clamp and then position it aside.
  6. Remove starter motor. Refer to STR, "Removal and Installation".
  7. Remove front drive shafts. Refer to FAX, "Removal and Installation".
  8. Set a suitable jack to transaxle assembly and then set a suitable jack to engine assembly.

CAUTION: When setting a suitable jack, be careful that it does not contact the position switch.

REMOVAL

20.   Remove engine mounting frame support (LH) bolts.

a. Remove bolt (A).

: Front

b. Release clutch damper (1) from bracket. Refer to CL, "Removal and Installation".

c. Remove bolt (B).

d. Remove engine mounting bracket (LH) bolts from vehicle. Refer to EM, "Exploded View".

21.   Remove rear engine mounting bracket and rear torque rod.

Refer to EM, "Exploded View".

22.   Remove transaxle assembly bolts and nuts.

23.   Remove transaxle assembly from the engine.

CAUTION:

  • Secure transaxle assembly to a suitable jack.
  • The transaxle assembly must not interfere with the wire harnesses and clutch tube.

REMOVAL

    24.   Remove engine mounting bracket (LH) from transaxle assembly. Refer to EM, "Exploded View".

    25.   Remove CSC. Refer to CL, "Removal and Installation".

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

  • Secure transaxle assembly to a suitable jack.
  • The transaxle assembly must not interfere with the wire harnesses and clutch tube.
  • When installing transaxle assembly, do not bring input shaft into contact with clutch cover.
  • Bolt hole is not threaded on new clutch housing. Self-tapping bolt is used to attach lock plate to clutch housing.
  • Do not reuse self-tapping bolt.
  • Tighten transaxle assembly bolts to the specified torque. The illustration is the view from the engine.                         

INSTALLATION

Inspection

INSPECTION AFTER INSTALLATION

  • Check the operation of the control linkage. Refer to TM, "Inspection".
  • Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required quantity, fill to the specified level. Refer to MA, "Fluids and Lubricants".
  • Use procedure below to check for fuel leakage.
  • Turn ignition switch ON (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leakage at connection points.
  • Start engine. With engine speed increased, check again for fuel leakage at connection points.
  • Run engine to check for unusual noise and vibration.

NOTE:If hydraulic pressure inside timing chain tensioner drops after removal and installation, slack in the guidemay generate a pounding noise during and just after engine start. However, this is normal. Noise will stopafter hydraulic pressure rises.

  • Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gas, or any oils/fluids includingengine oil and engine coolant.
  • Bleed air from passages in lines and hoses, such as in cooling system.
  • After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to specifiedlevel, if necessary.
  • Summary of the inspection items: 

*Power steering fluid, brake fluid, etc.

5Th main gear assembly

Removal and Installation REMOVAL Move the shift selector to the 3rd gear position. Disconnect the shifter cable and the selector cable from shifter lever A and selector lever. Refer to TM, ...

Other materials:

Stall test
Work Procedure INSPECTION Inspect the amount of engine oil. Replenish the engine oil if necessary. Refer to LU "Inspection". Drive for about 10 minutes to warm up the vehicle so that the A/T fluid temperature is 50 to 80C (122 to 176F). Inspect the amount of ATF. Replenish ...

Door check link
DOOR CHECK LINK : Removal and Installation REMOVAL Fully close the rear door window. Remove rear door finisher. Refer to INT "Removal and Installation". Remove rear door speaker bolts (if equipped). Disconnect harness connector and remove rear door speaker (if equipped). Rem ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0225