Nissan Versa (N17): Precautions

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"

The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.

Information necessary to service the system safely is included in the SR and SB section of this Service Manual.

WARNING:

  • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer.
  • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SR section.
  • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

  • When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury.
  • When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery and wait at least three minutes before performing any service.

Precaution for Procedure without Cowl Top Cover

When performing the procedure after removing cowl top cover, cover the lower end of windshield with urethane, etc to prevent damage to windshield.

Precaution for Procedure without Cowl Top Cover

PREPARATION

Commercial Service Tool

Commercial Service Tool

SYSTEM DESCRIPTION

COMPONENT PARTS

Component Parts Location

Component Parts Location

1. IPDM E/R 2. Windshield washer tank (view with RF fender protector removed) 3. Front washer motor (view with RF fender protector removed) 4. Front wiper motor (view with cowl top removed) 5. Combination switch (wiper and washer switch) 6. BCM (view with instrument panel removed)

Component Description

Component Function
BCM - Monitors combination switch status by performing the combination switch reading function.

- Sends front wiper relay and front wiper high relay ON signals to IPDM E/R.

IPDM E/R - Controls front wiper relay and front wiper high relay.

- Performs the auto stop control of the front wiper.

Combination switch (Wiper and washer switch) - Provides input for wiper and washer control to BCM.

- Refer to WW "System Description" for more information.

Front wiper motor - Drives windshield wipers in HI or LO mode.

- Sends wiper stop signal to IPDM E/R.

Front washer motor Pumps windshield washer fluid to windshield in wash mode.

Trunk room lamp

Exploded View 1. Trunk room lamp 2. Bulb Front Pawl ...

System

System Diagram System Description FRONT WIPER CONTROL (BASIC) 1. BCM detects the combination switch position by the combination switch reading function. 2. BCM transmits the front wiper ...

Other materials:

Power supply and ground circuit
Diagnosis Procedure 1.CHECK GROUND CONNECTION Turn ignition switch OFF. Check ground connection E. Refer to Ground Inspection in GI, "Circuit Inspection". Is the inspection result normal? YES >> GO TO 2. NO >> Repair or replace ground connection. 2.CHECK ECM G ...

P0711 Transmission fluid temperature sensor A
DTC Logic DTC DETECTION LOGIC DTC Trouble diagnosis name DTC detection condition Possible causes P0711 Transmission Fluid Temperature Sensor "A" Circuit Range/ Performance Under the following diagnosis conditions, A/T fluid temperature does not rise to ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0082