Nissan Versa (N17): Precautions
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER",
used along
with a front seat belt, helps to reduce the risk or severity of injury to the
driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage
front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment,
and may only deploy one front
air bag, depending on the severity of a collision and whether the front
occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB
section of this Service Manual.
WARNING:
- To avoid rendering the SRS inoperative, which could increase the
risk of personal injury or death in
the event of a collision which would result in air bag inflation, all
maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
- Improper maintenance, including incorrect removal and installation
of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of
Spiral Cable and Air Bag
Module, see the SR section.
- Do not use electrical test equipment on any circuit related to the
SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or
orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
- When working near the Airbag Diagnosis Sensor Unit or other Airbag
System sensors with the Ignition
ON or engine running, DO NOT use air or electric power tools or strike near
the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air
bag(s), possibly causing
serious injury.
- When using air or electric power tools or hammers, always switch
the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Seat Belt Service
CAUTION:
- Before removing the seat belt pre-tensioner assembly, turn the
ignition switch OFF, disconnect both
battery terminals and wait at least three minutes. For approximately three
minutes after the battery
terminals have been removed, it is still possible for the air bag and seat
belt pre-tensioner to deploy.
Therefore, do not attempt work on any SRS connectors or wires until at least
three minutes have
passed.
- After replacing or reinstalling seat belt pre-tensioner assembly
or reconnecting seat belt pre-tensioner
assembly connector, make sure entire SRS operates properly. Refer to SRC
"SRS Operation
Check".
- Do not disassemble buckle or seat belt assembly.
- Replace anchor bolts if they are deformed or worn out.
- Do not oil tongue or buckle.
- If any component of seat belt assembly is questionable, do not
repair. Replace the whole seat belt
assembly.
- If webbing is cut, frayed or damaged, replace seat belt assembly.
- When replacing seat belt assembly, use a Genuine NISSAN seat belt
assembly.
BASIC INSPECTION
Inspection
AFTER A COLLISION
WARNING:
Inspect all seat belt assemblies including retractors and attaching hardware
after any collision.
NISSAN/INFINITI recommends that all seat belt assembli ...
Other materials:
Front fender
FRONT FENDER : Removal and Installation
CAUTION:
Use a shop cloths to protect the body from being damaged during removal and
installation.
REMOVAL
Remove fender protector. Refer to EXT "Removal and Installation".
Remove front bumper fascia and bumper side bracket. Refer to EXT
...
Front wiper does not operate
Description
The front wiper does not operate under any operation conditions.
Diagnosis Procedure
Regarding Wiring Diagram information, refer to WW "Wiring Diagram".
1. CHECK WIPER RELAY OPERATION
IPDM E/R AUTO ACTIVE TEST
1. Start IPDM E/R auto active test. Refer to PCS "CONSULT ...
© 2017-2025 Copyright www.niveguide.com
0.0094