Nissan Versa

 Sedan Service Manual

Ventilation, heater & air conditioner » Ventilation system (VTL) » Precautions
Precaution for Work

• When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:

• Water soluble dirt:

• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.

• Oily dirt:

• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.

• Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.

PREPARATION

Special Service Tool

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tool

SYSTEM DESCRIPTION

VENTILATION SYSTEM

VENTILATION SYSTEM (FRONT AIR CONDITIONING)

VENTILATION SYSTEM (FRONT AIR CONDITIONING) : System Description

OUTLINE

The ventilation system is controlled by the A/C control. For details of the air conditioner system, refer to VTL "VENTILATION SYSTEM (FRONT AIR CONDITIONING) : System Description".

AIR FLOW

Front

REMOVAL AND INSTALLATION

DUCT AND GRILLE

Exploded View

1. A/C unit assembly 2. Foot duct (LH) 3. Foot duct (RH) 4. Side ventilator grille (LH) 5. Center ventilator grille (LH) 6. Cluster lid C 7. Center ventilator grille (LH) 8. Instrument panel assembly 9. Side ventilator grille (RH) 10. Center ventilator duct assembly

CENTER VENTILATOR GRILLE

CENTER VENTILATOR GRILLE : Removal and Installation

REMOVAL

1. Remove cluster lid C. Refer to IP "Removal and Installation".
2. Release the tabs and remove the center ventilator grille from cluster lid C.

INSTALLATION

Installation is in the reverse order of removal.

SIDE VENTILATOR GRILLE

SIDE VENTILATOR GRILLE : Removal and Installation

REMOVAL

1. Remove the instrument panel assembly. Refer to IP "Removal and Installation".
2. Remove the center ventilator duct assembly.
3. Remove the side ventilator grille screw and remove the side ventilator grille from the instrument panel assembly.

INSTALLATION

Installation is in the reverse order of removal.

CENTER VENTILATOR DUCT

CENTER VENTILATOR DUCT : Removal and Installation

REMOVAL

1. Remove the instrument panel assembly. Refer to IP "Removal and Installation".
2. Remove the center ventilator duct assembly screws and the center ventilator duct assembly from the instrument panel assembly.

INSTALLATION

Installation is in the reverse order of removal.

FOOT DUCT

FOOT DUCT : Removal and Installation

LEFT SIDE

Removal

1. Remove the A/C unit assembly. Refer to HA "Removal and Installation".
2. Remove the foot duct (LH) screws and the foot duct (LH).

Installation

Installation is in the reverse order of removal.

RIGHT SIDE

Removal

1. Remove the instrument panel assembly. Refer to IP "Removal and Installation".
2. Remove the foot duct (RH) screws and the foot duct (RH).

Installation

Installation is in the reverse order of removal.

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"

Precaution for Work