Nissan Versa (N17): P2135 TP sensor

DTC Logic

DTC DETECTION LOGIC

NOTE: If DTC P2135 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to EC, "DTC Logic".

DTC No. Trouble diagnosis name DTC detecting condition Possible cause
P2135 Throttle position sensor circuit range/performance Rationally incorrect voltage is sent to ECM compared with the signals from TP sensor 1 and TP sensor 2.
  • Harness or connector (TP sensor 1 and 2 circuit is open or shorted.)
  • Electric throttle control actuator (TP sensor 1 and 2)

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION: Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 1 second.
  2. Check DTC.

Is DTC detected?

YES >> Go to EC, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK GROUND CONNECTION

  1. Turn ignition switch OFF.
  2. Check ground connection E15. Refer to Ground Inspection in GI, "Circuit Inspection".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CHECK THROTTLE POSITION SENSOR POWER SUPPLY CIRCUIT

  1. Disconnect electric throttle control actuator harness connector.
  2. Turn ignition switch ON.
  3. Check the voltage between electric throttle control actuator harness connector and ground. 

Is the inspection result normal?

YES >> GO TO 3.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

3.CHECK THROTTLE POSITION SENSOR GROUND CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between electric throttle control actuator harness connector and ground.
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> GO TO 4.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

4.CHECK THROTTLE POSITION SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

  1. Check the continuity between electric throttle control actuator harness connector and ground.
  2. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> GO TO 5.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

5.CHECK THROTTLE POSITION SENSOR

Refer to EC, "Component Inspection".

Is the inspection result normal?

YES >> GO TO 7.

NO >> GO TO 6.

6.REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR

Replace electric throttle control actuator. Refer to EM, "Removal and Installation".

>> INSPECTION END

7.CHECK INTERMITTENT INCIDENT

Refer to GI, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK THROTTLE POSITION SENSOR

  1. Turn ignition switch OFF.
  2. Reconnect all harness connectors disconnected.
  3. Perform EC, "Work Procedure".
  4. Turn ignition switch ON.
  5. Set selector lever to D (A/T or CVT) or 1st (M/T) position.
  6. Check the voltage between ECM harness connector and ground.   

Is the inspection result normal?

YES >> INSPECTION END

NO >> GO TO 2.

2.REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR

Replace electric throttle control actuator. Refer to EM, "Removal and Installation".

>> INSPECTION END

Other materials:

Parking brake
WARNING Be sure the parking brake is fully released before driving. Failure to do so can cause brake failure and lead to an accident. Do not release the parking brake from outside the vehicle. Do not use the shift lever in place of the parking brake. When parking, be sure the par ...

PLUG
Description Replace the O-ring if oil leakage or exudes from the plug. Exploded View 1. Plug 2. O-ring 3. O-ring 4. Plug Genuine NISSAN CVT Fluid NS-3 Removal and Installation REMOVAL Remove the plugs and O-rings. INSTALLATION Installation is in the reverse order of removal. CAUT ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0111