Nissan Versa (N17): P0979 Shift solenoid C

Nissan Versa 2nd generation (N17) Service Manual / Transmission & driveline / Transaxle & transmission (TM) / P0979 Shift solenoid C

DTC Logic

DTC DETECTION LOGIC

DTC Trouble diagnosis name DTC detection condition Possible causes
P0979 Shift Solenoid C Control Circuit Low The following diagnosis conditions are met, and the current monitor reading of the TCM 2-4 brake solenoid valve is 200 mA or less continuously for 0.5 seconds or more.

- Diagnosis condition

- Solenoid valve output current: 750 mA or more

- GND short circuit diagnosis occurs in the solenoid valve drive circuit.

- TCM power supply voltage: 10 V < TCM power supply voltage < 16 V

- Harness or connector (Short circuit to ground in the 2-4 brake solenoid valve circuit)

- 2-4 brake solenoid valve

DTC REPRODUCTION PROCEDURE

CAUTION: Be careful of the driving speed.

1.PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

  1. Drive the vehicle.
  2. Maintain the following conditions for 5 seconds or more.

Selector lever : 2 position

Gear : 2GR

Vehicle speed : 20 km/h (13 MPH) or more

  1. Stop the vehicle.
  2. Check the first trip DTC.

Is "P0979" detected?

YES >> Go to TM, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK CIRCUIT BETWEEN TCM AND A/T UNIT

  1. Turn ignition switch OFF.
  2. Disconnect the TCM connector and A/T unit connector.
  3. Check the continuity between TCM harness connector and ground.

Is the check result normal?

YES >> GO TO 2.

NO >> Repair or replace the malfunctioning parts.

2.CHECK 2-4 BRAKE SOLENOID VALVE

Check the 2-4 brake solenoid valve. Refer to TM, "Component Inspection (2-4 Brake Solenoid Valve)".

Is the check result normal?

YES >> Check intermittent incident. Refer to GI, "Intermittent Incident".

NO >> Repair or replace the malfunctioning parts.

Component Inspection (2-4 Brake Solenoid Valve)

1.CHECK 2-4 BRAKE SOLENOID VALVE

Check the resistance between the A/T unit connector and ground. 

Is the check result normal?

YES >> INSPECTION END

NO >> There is a malfunction of the 2-4 brake solenoid valve. Replace the transaxle assembly. Refer to TM, "Removal and Installation".

P0977 Shift solenoid B

DTC Logic DTC DETECTION LOGIC DTC Trouble diagnosis name DTC detection condition Possible causes P0977 Shift Solenoid B Control Circuit High The following diagnosi ...

P0980 Shift solenoid C

DTC Logic DTC DETECTION LOGIC DTC Trouble diagnosis name DTC detection condition Possible causes P0980 Shift Solenoid C Control Circuit High The following diagnosis ...

Other materials:

Fuel pressure check
Work Procedure FUEL PRESSURE RELEASE 1.FUEL PRESSURE RELEASE With CONSULT Turn ignition switch ON. Perform "FUEL PRESSURE RELEASE" in "WORK SUPPORT" mode with CONSULT. Start engine. After engine stalls, crank it two or three times to release all fuel pressure. Turn ignition switc ...

IDLE SPEED
Inspection 1.CHECK IDLE SPEED With CONSULT Check idle speed in "DATA MONITOR" mode with CONSULT. Without CONSULT Check idle speed by installing the pulse type tachometer clamp on the loop wire or on suitable high-tension wire which installed between No.1 ignition coil and No.1 spark plug. ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0076