Nissan Versa (N17): P0743 Torque converter

Nissan Versa 2nd generation (N17) Service Manual / Transmission & driveline / Transaxle & transmission (TM) / P0743 Torque converter

DTC Logic

DTC DETECTION LOGIC

DTC Trouble diagnosis name DTC detection condition Possible causes
P0743 Torque Converter Clutch Circuit Electrical The following diagnosis conditions are met, and the TCM torque converter clutch solenoid valve current monitor reading is 200 mA or less continuously for 0.5 seconds or more.

- Diagnosis condition

- Solenoid valve output current: 750 mA or more

- GND short circuit diagnosis occurs in the solenoid valve drive circuit.

- TCM power supply voltage: 10 V < TCM power supply voltage < 16 V

- Harness or connector (Short circuit to ground in the torque converter clutch solenoid valve circuit)

- Torque converter clutch solenoid valve

DTC CONFIRMATION PROCEDURE

CAUTION: Be careful of the driving speed.

1.PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

  1. Drive the vehicle.
  2. Maintain the following conditions for 5 seconds or more.

Selector lever : D position

Vehicle speed : 45 km/h (28 MPH) or more

    3.   Stop the vehicle.

    4.   Check the first trip DTC.

Is "P0743" detected?

YES >> Go to TM, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK CIRCUIT BETWEEN TCM AND A/T UNIT

  1. Turn ignition switch OFF.
  2. Disconnect the TCM connector and A/T unit connector.
  3. Check the continuity between TCM harness connector and ground. 

Is the check result normal?

YES >> GO TO 2.

NO >> Repair or replace the malfunctioning parts.

2.CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE

Check the torque converter clutch solenoid valve. Refer to TM, "Component Inspection (Torque Converter Clutch Solenoid Valve)".

Is the check result normal?

YES >> Check intermittent incident. Refer to GI, "Intermittent Incident".

NO >> Repair or replace the malfunctioning parts.

Component Inspection (Torque Converter Clutch Solenoid Valve)

1.CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE

Check the resistance between the A/T unit connector terminal and ground. 

Is the check result normal?

YES >> INSPECTION END

NO >> There is a malfunction of the torque converter clutch solenoid valve. Replace the transaxle assembly. Refer to TM, "Removal and Installation".

P0740 Torque converter

DTC Logic DTC DETECTION LOGIC DTC Trouble diagnosis name DTC detection condition Possible causes P0740 Torque Converter Clutch Circuit/ Open The follow diagnosis co ...

P0744 Torque converter

Description This DTC is detected when the torque converter clutch solenoid valve is electrically normal but the torque converter clutch does not engage. This is not due to an electrical malfunctio ...

Other materials:

Steering wheel
Tilt operation Push the lock lever 1 down and adjust the steering wheel up or down 2 to the desired position. Pull the lock lever 1 up to lock the steering wheel in place. WARNING Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accid ...

Fuel level sensor unit, fuel filter and fuel pump assembly
Exploded View 1. Lock ring 2. Fuel level sensor unit, fuel filter and fuel pump assembly 3. O-ring 4. Fuel tank Removal and Installation WARNING: Be sure to read "General Precautions" before working on the fuel system. Refer to FL, "General Precautions". REMOVAL Release t ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0082