Nissan Versa (N17): C1708, C1709, C1710, C1711 Transmitter (no data)

Nissan Versa 2nd generation (N17) Service Manual / Suspension / Road wheels & tires (WT) / C1708, C1709, C1710, C1711 Transmitter (no data)

DTC Logic

NOTE: The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.

  • Activate and display TPMS transmitter IDs
  • Display tire pressure reported by the TPMS transmitter
  • Read TPMS DTCs
  • Register TPMS transmitter IDs

DTC DETECTION LOGIC       

DTC CONFIRMATION PROCEDURE

1.PERFORM SELF DIAGNOSTIC RESULT

With CONSULT

  1. Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
  2. Stop the vehicle.
  3. Perform "SELF DIAGNOSTIC RESULT".

Is DTC "C1708", "C1709", "C1710" or "C1711" detected?

YES >> Proceed to WT "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

NOTE: The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.

  • Activate and display TPMS transmitter IDs
  • Display tire pressure reported by the TPMS transmitter
  • Read TPMS DTCs
  • Register TPMS transmitter IDs

Regarding Wiring Diagram information, refer to WT "Wiring Diagram".

1.CHECK DATA MONITOR

With CONSULT

  1. Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
  2. Stop the vehicle.
  3. On "DATA MONITOR" select "AIR PRESS FL", "AIR PRESS FR", "AIR PRESS RR" and "AIR PRESS RL".
  4. Within 5 minutes after vehicle is stopped, read the values displayed on CONSULT.

Are all tire pressures displayed 0 kPa (psi)?

YES >> GO TO 2.

NO >> GO TO 5.

2.CHECK REMOTE KEYLESS ENTRY RECEIVER POWER CIRCUIT

Check voltage between remote keyless entry receiver connector and ground.   

Is the inspection result normal?

YES >> GO TO 3.

NO >> Repair or replace harness or connectors.

3.CHECK REMOTE KEYLESS ENTRY RECEIVER SIGNAL CIRCUIT

  1. Turn the ignition switch OFF.
  2. Disconnect BCM and remote keyless entry receiver connectors.
  3. Check continuity between BCM and remote keyless entry receiver connectors.   

    4.   Check continuity between BCM connector and ground.  

Is the inspection result normal?

YES >> GO TO 4.

NO >> Repair or replace the malfunctioning harness or connector.

4.CHECK REMOTE KEYLESS ENTRY RECEIVER GROUND CIRCUIT

Check continuity between BCM and remote keyless entry receiver connectors.

Is the inspection result normal?

YES >> GO TO 5.

NO >> Repair or replace the malfunctioning harness or connector.

5.TRANSMITTER ID REGISTRATION

Perform transmitter ID registration. Refer to WT "Work Procedure".

Is transmitter ID registration completed?

YES >> GO TO 6.

NO >> Replace applicable transmitter. Refer to WT "Removal and Installation".

6.CHECK TIRE PRESSURE SIGNAL

With CONSULT

  1. Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
  2. Stop the vehicle.
  3. On "DATA MONITOR" select "AIR PRESS FL", "AIR PRESS FR", "AIR PRESS RR" and "AIR PRESS RL".
  4. Within 5 minutes after vehicle stopped, check that the tire pressures are within specification. Refer to WT- "Tire Air Pressure".   

Is the inspection result normal?

YES >> Inspection End.

NO >> Replace the BCM. Refer to BCS "Removal and Installation" or BCS "Removal and Installation".

C1704, C1705, C1706, C1707 Low tire pressure

DTC Logic DTC DETECTION LOGIC            DTC CONFIRMATION PROCEDURE 1.PERFORM SELF DIAGNOSTIC RESULT With CONSULT Turn the ignition sw ...

Other materials:

Vehicle loading information
WARNING It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be ...

Diagnosis and repair work flow
Work Flow NOTE: The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information. Activate and display TPMS transmitter IDs Display tire pressure reported by the TPMS transmitter Read TPMS DTCs Register ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0065