Nissan Versa (N17): B1145 - B1148 Side curtain air bag module RH

Nissan Versa 2nd generation (N17) Service Manual / Restraints / SRS Airbag control system (SRC) / B1145 - B1148 Side curtain air bag module RH

Description

DTC B1145 - B1148 RH SIDE CURTAIN AIR BAG MODULE

The RH side curtain air bag module is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the RH side curtain air bag module.

PART LOCATION

Refer to SRC "Component Parts Location".

DTC Logic

DTC DETECTION LOGIC

With CONSULT       

Without CONSULT       

DTC CONFIRMATION PROCEDURE (With CONSULT)

1.CHECK SELF-DIAG RESULT

  1. Turn ignition switch ON.
  2. Check for DTC using CONSULT.

Is the DTC detected?

YES (Current DTC)>>Refer to SRC "Diagnosis Procedure".

YES (Past DTC)>>GO TO 2.

NO >> Inspection End.

2.ERASE SELF-DIAG RESULT

Erase the DTC using CONSULT.

Can the DTC be erased?

YES >> Inspection End.

NO >> Refer to SRC "Diagnosis Procedure".

DTC CONFIRMATION PROCEDURE (Without CONSULT)

1.CHECK SELF-DIAG RESULT

  1. Turn ignition switch ON.
  2. Check the air bag warning lamp status. Refer to SRC "Trouble Diagnosis without CONSULT".

NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode.

Is the DTC detected?

YES >> Refer to SRC "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

1.HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

  • Visible damage to connector or terminal
  • Loose terminal
  • Poor connection

NOTE: All harness connectors should be inspected from the air bag diagnosis unit to the end component (including any in-line connectors).

Is the inspection result normal?

YES >> GO TO 2.

NO >> Perform one of the following repairs:

  • Visible damage: Replace the harness.
  • Loose terminal: Secure the terminal.
  • Poor connection: Secure the connection.

2.CONFIRM DTC

  1. Reconnect all harness connectors.
  2. Turn ignition switch ON.
  3. Check for DTC using CONSULT.

Is DTC still current?

YES >> GO TO 3.

NO >> Refer toGI "Intermittent Incident".

3.WIRING HARNESS

Check the wiring harness for visible damage NOTE.

NOTE: The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors).

Is the inspection result normal?

YES >> GO TO 4.

NO >> Replace the harness.

4.CONFIRM DTC

  1. Reconnect all harness connectors.
  2. Turn ignition switch ON.
  3. Check for DTC using CONSULT.

Is DTC still current?

YES >> GO TO 5.

NO >> Refer to GI "Intermittent Incident".

5.AIR BAG DIAGNOSIS SENSOR UNIT

  1. Replace the air bag diagnosis sensor unit. Refer to SR "Removal and Installation".
  2. Turn ignition switch ON.
  3. Check for DTC using CONSULT.

Is DTC still current?

YES >> GO TO 6.

6.SIDE CURTAIN AIR BAG MODULE RH

  1. Replace the side curtain air bag module RH. Refer to SR "Removal and Installation".
  2. Turn ignition switch ON.
  3. Check for DTC using CONSULT.

Is DTC still current?

YES >> GO TO 7.

NO >> Clear DTC. Inspection End.

7.RELATED HARNESS

Replace the related harness.

>> END

B1150 - B1153 Side curtain air bag module LH

Description DTC B1150 - B1153 LH SIDE CURTAIN AIR BAG MODULE The LH side curtain air bag module is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for ...

B1086 - B1089 Seat belt pre-tensioner LH

Description DTC B1086 - B1089 SEAT BELT PRE-TENSIONER LH The seat belt pre-tensioner LH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for opens and ...

Other materials:

Clutch pedal
Inspection and Adjustment 1.   Check to see if the master cylinder rod end moves freely. It should not be bound by the clutch pedal. a. If the rod end does not move freely, remove the rod end and check for deformation or damage on the rod end. Leave the rod end removed ...

Slip indicator lamp
Component Function Check 1.CHECK SLIP INDICATOR LAMP FUNCTION Check that slip indicator lamp in combination meter turns ON for approximately 2 seconds after ignition switch is turned ON. Is the inspection result normal? YES >> Inspection End. NO >> Proceed to diagnosis procedure. ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0101